Thermos replacement: the mistakes that cost you
Replacing a thermos (sealed glass unit) looks simple on the surface, but it hides several pitfalls for the uninitiated. A mistake in measuring, in choosing the product or in the installation can turn a smart investment into a source of recurring problems. Here are the 7 most common mistakes and how to avoid them.
Mistake #1: Taking the wrong measurements
This is the most frequent and the most expensive mistake. A custom-made thermos that doesn't match the exact dimensions of your opening is unusable.
What to do
- Measure the width and height of the glass, not the full frame.
- Take measurements at three points (top, middle, bottom for the width; left, centre, right for the height) and keep the smallest one.
- Measure the total thickness of the existing sealed unit, including the air space.
- Note the type of spacer and its width.
When in doubt, call a professional. At Vosthermos, measuring is included in our services.
Mistake #2: Choosing the cheapest thermos without checking the specs
Not all thermos units are equal. An unusually low price often hides compromises on quality:
- No argon gas: units filled with dry air insulate less.
- No Low-E coating: heat loss will be significantly higher.
- Single seal instead of the industry-standard dual seal.
- No recognized certification (IGMA or IGCC): no assurance that the unit meets industry standards.
The initial savings often turn into double the expense when the low-end thermos has to be replaced after only 5 to 8 years. Read our article on clearance thermos units to learn more.
Mistake #3: Ignoring the condition of the frame
Replacing a thermos in a rotten or warped frame is a waste of money. Before the replacement, check:
- The wood: rot, mould or insect damage.
- The aluminum or vinyl: warping, cracks, excessive discolouration.
- The drainage: the weep holes must be clear and functional.
- The squareness: a frame that is no longer plumb will put uneven pressure on the new thermos.
If the frame is damaged, it's better to repair or replace it at the same time as the thermos.
Mistake #4: Forgetting to check the type of glazing required by code
The Quebec Construction Code requires safety glass (tempered or laminated) in certain locations, notably:
- in glazed doors and patio doors;
- in glazed panels next to a door that could be mistaken for an opening;
- in shower and bathtub enclosures.
Installing ordinary glass where the code requires safety glass creates a risk of injury and can complicate the resale of your property. When in doubt, check before ordering: the Régie du bâtiment du Québec and your installer can advise you.
Mistake #5: Installing the setting blocks incorrectly
Setting blocks are the small plastic or rubber blocks that support the weight of the thermos in the frame. Incorrect installation leads to:
- Uneven pressure on the seal, which speeds up its deterioration.
- Sagging of the thermos, which jams the window's mechanisms.
- Glass-to-metal contact points that can cause thermal fracture.
The blocks should be positioned one quarter of the width in from each corner, and never directly in the corners.
Mistake #6: Neglecting the sealing and the caulking
The new thermos is installed, but if the joint between the glass and the frame isn't properly sealed, moisture will get in and cause:
- Premature condensation between the panes.
- Mould in the frame.
- A loss of insulation around the thermos.
Use a quality caulking compound that is compatible with the frame type and the glass type. Both interior and exterior caulking are necessary.
Mistake #7: Attempting a replacement in extreme weather
Replacing a thermos at -20°C in January or at 40°C in the sun in midsummer is a bad idea:
- In extreme cold: sealing compounds don't cure properly below 5°C. Cold glass coming into contact with warm indoor air undergoes thermal shock.
- In extreme heat: expanded glass can break during handling, and sealants dry too fast to allow precise positioning.
The ideal temperature for sealing a thermos is between 10°C and 25°C. A professional can still replace a pane in the dead of winter: it's the exterior caulking that sometimes waits for a milder spell.
The solution: call in professionals
Replacing a thermos is precision work that requires experience and the right tools. At Vosthermos, our qualified technicians know these mistakes and know how to avoid them. Every installation is done to industry standards, with certified products and a full warranty.
Check our transparent prices for thermos replacement or visit our online store to discover our sealed units. Request your free quote today.

